Deployment Choice: Manila Network Plugins¶

Warning

The NetApp driver only supports provisioning share servers (ONTAP SVMs) on non-segmented (FLAT) networks and VLAN networks. While tenants may be deployed on overlay networks (GRE, VXLAN, GENEVE), Manila shares are only accessible over FLAT networks or VLAN networks.

Your deployment options are:

Overlay tenant network + Provider Network: Deploy nova instances within a VXLAN tenant network dedicated to the tenant, but access file shares over a FLAT or VLAN shared provider network.
VLAN tenant network: In this case, tenant networks are VLAN networks. In this case, the networking service assigns a new VLAN segment when a tenant creates a private network. This dedicated private network can be used to deploy the tenant’s Nova instances as well as access their file shares.

Neutron Overview¶

OpenStack’s networking-as-a-service project is codenamed Neutron. Neutron offers self service networking APIs to tenants. Tenant networks are typically segmented virtual networks that are isolated between each other and provide east-west network routing within the OpenStack installation. For packets to flow into external networks, including the internet, routers are created and attached to the indicated networks as necessary. For in-flow, Network Address Translation (NAT) is employed and IP addresses in the tenant router namespace are mapped to IP addresses in the external network namespace.

Network Types¶

Aside from tenant networks, administrators can create “provider” networks on Neutron, and share them with their OpenStack tenants. Such networks can either be segmented or non-segmented (FLAT). On a FLAT network, everyone shares the same network segment and hence there isn’t any isolation of network traffic. There’s usually a very good reason to use FLAT networks in OpenStack, such as sharing a dedicated high bandwidth storage network with all tenants. In such scenarios, network traffic is usually encrypted end-to-end providing logical isolation of cross tenant traffic. Overlapping IP and subnet ranges is not possible in this networking model.

Network Segmentation¶

Network segmentation is often accomplished using (VLANs). Administrators may allow tenants to create VLAN networks. In this case, each tenant network is assigned its own VLAN ID, and cross tenant traffic is isolated at layer-2. Subnets and IP ranges are allowed to safely overlap between tenant networks when the tenant networks are isolated in separate VLANs. OVS (Open vSwitch) has an ML2 plugin in Neutron that allocates internal VLANs on each compute host. OVS creates the tunnel bridges necessary to route packets between these VLAN networks. When combined with a hardware plugin such as the Cisco Nexus plugin, VLANs are allocated on the external hardware as well. Typically storage devices like NetApp ONTAP Fabric-Attached Storage (FAS) are configured on these hardware devices in a trunk configuration. VLANs are then created and managed with the help of the hardware switch vendor’s ML2 plugin mechanism driver in Neutron.

Keep in mind that VLANs are limited to the range of 1 to 4094. When using VLANs, no more than 4092 isolated networks can exist. Keep this scaling limitation in mind when designing your OpenStack environment. Other encapsulation methodologies aim to solve this problem by encapsulating network packets with a larger virtual networking identifier. GRE (Generic Routing Encapsulation), GENEVE (Generic Network Virtualization Encapsulation) and VXLAN (Virtual Extensible LAN) are the popular standards used with OpenStack deployments.

ONTAP does not natively support these layer-3 SDN network standards. Deployers have the choice of using administrator configured VLAN-only provider networks or VLAN-only tenant networks if using Neutron.

Network Plugins¶

As described in Figure 6.2. Manila Workflow - Share Creation with Share Servers, there are a set of network plugins that provide for a variety of integration approaches with Neutron and Standalone networks. These plugins should only be used with the NetApp ONTAP driver when using share server management.

These are the valid network plugins:

Standalone Network Plugin: Use this plugin in stand-alone deployments of OpenStack Manila, and in deployments where you don’t desire to manage the storage network with Neutron.
Simple Neutron Network Plugin: This is like the Standalone Network Plugin, except that the network is managed by Neutron.
Configurable Neutron Network Plugin: This is like the Simple Network Neutron Plugin except that except that each share network object will use a tenant or provider network of the tenant’s choice.
Simple Neutron Port Binding Network Plugin: This plugin is very similar to the simple Neutron network plugin, the only difference is that this plugin can enforce port-binding.
Configurable Neutron Port Binding Network Plugin: This plugin is very similar to the configurable neutron network plugin, the only difference is that this plugin can enforce port-binding.

The network plugin is chosen by setting the value of the network_api_class configuration option within the driver-specific stanza of the manila.conf configuration file.